Sentry Sentry 2.0 Instruções de Operação descarregar pdf (Página 23)

pre-20A software: Select or —whichever

appears.)

From ,press repeatedly until

or appears.

Press . Use the and keys to select

or .

After selecting one of the above, press . Press

to return to .

RATE / Types of Rates

Note: This feature is included on controllers with

software version 18D or newer. To look up your soft

ware version, see the SOFT option, page 25.

The standard method of programming firing rate is de

grees of temperaturechange perHOUR. Atthe factory, we

can set up your controller to calculate rate instead as de

grees of temperature change per MINUTE, or as

ELAPSED TIME needed to reach a temperature. The

RATE option shows you which method your controller

uses:

From ,press repeatedly until

appears.

Press . You will see one of the following:

(Degrees of temperature change per hour)

(Degrees of temperature change per minute)

(Elapsed time needed to reach a temperature)

Only the factory can change the type of rate used in your

controller.

Note: If your controller uses TIME rate, enter the

hours/minutes that each segment will take to reach its

target temperature. (Example: 1 hour, 30 minutes =

01.30.)

COST / Electric Cost Per

Kilowatt-Hour

Note: This feature is included on controllers with

software version 18D or newer. To look up your soft

ware version, see the SOFT option, page 25.

The controller can figure the cost of a firing if you enter

the cost of electricity for your area (and kiln wattage—see

next option). The cost of electricity is figured in kilo

watt-hours (KWh). A kilowatt-hour is 1,000 watts of elec

tricity running for 1 hour. (10 – 100-watt light bulbs glowing

for one hour consume 1 KWh of electricity.)

To find what the power company charges you for a kilo

watt-hour, look at your electric bill, call your power com

pany, or visit their website. The electric rate may vary de

pending on the time of year and amount of electricity you

use. In the summer, rates in some areas are higher. Also,

add the other costs listed on your electric bill, such as power

transmission charges, taxes, etc.

From ,press repeatedly until

appears. Press .

From an electric bill, enter the cost of a kilo

watt-hour. Place cents to the right of the decimal.

Round off fractions. (Example: Enter 9.25 cents per

kilowatt-hour as 00.09.) Press .

Press to return to .

Note: You can enter the cost in U. S., Canadian, or

Euro cents, British pence, Indian paisas, or any other

money system that is based upon 100 units (i.e. 100

cents = 1 dollar.) If your system is based upon 1000

units, such as the Libyan dirham, the Oman baiza, or

the Kuwait fil, divide the cost by 10. Example: Enter

140 as 00.14. Then multiply by 10 the cost of a firing

shown in the controller display.

KW / Kilowatts Used to Calculate

Firing Cost

Note: This feature is included on controllers with

software version 18D or newer. To look up your soft

ware version, see the SOFT option, page 25.

To figure the cost to fire your kiln, the controller needs

to know how many kilowatts your kiln uses. Look at your

kiln’s electrical data plate. It is usually on the side of the

switch box. The data plate lists the watts, amps, and volts. If

watts are not listed, multiply amps x volts. (Example: 15

amps x 240 volts = 3,600 watts.)

Divide the wattage of your kiln by 1000, which gives the

kilowatts. (Move the decimal point 3 spaces to the left.)

Examples:

10,800 watts ÷ 1000 = 010.8

4,800 watts ÷ 1000 = 004.8

800 watts ÷ 1000 = 000.8

Enter that amount in the KW option:

From , press repeatedlyuntil

appears. Press .

The controller shows 4 digits for entering kilowatts:

. Enter kilowatts for your kiln.

Press .

Press to return to .

Note: Please do not confuse kilowatts with kilo

watt-hours. A kilowatt is 1,000 watts. A kilowatt-hour

is 1,000 watts powered for one hour.

To view the cost of a firing, press the key after the kiln

has fired to completion and flashes.

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 39 40

Comentários a estes Manuais

Sem comentários

Senco RoofPro 455XP Manual de usuario (2 paginas)

Marca: Senco | Categoria: Tools | Tamaño: 1.08 MB |

Tabla de contenidos

XtremePro

1¾" Coil Roofing Nailer

Más productos y manuales para Herramientas Senco

Modelos	Tipo de documento
FinishPro 15	Manual de usuario Senco FinishPro 15 User Manual, 12 paginas
Pneumatic SHF50	Manual de usuario Senco Pneumatic SHF50 User Manual, 2 paginas
SFN40	Manual de usuario Senco SFN40 User Manual, 8 paginas
42XP	Manual de usuario Senco 42XP User Manual, 2 paginas
PW-2	Manual de usuario Senco PW-2 User Manual, 2 paginas
YK0320	Manual de usuario Senco YK0320 User Manual, 4 paginas
25	Manual de usuario Senco 25 User Manual, 22 paginas
SLS20HF	Manual de usuario Senco SLS20HF User Manual, 12 paginas
SFN1	Manual de usuario Senco SFN1 User Manual, 16 paginas
SQS55	Manual de usuario Senco SQS55 User Manual, 4 paginas
XtremePro MWXP	Manual de usuario Senco XtremePro MWXP User Manual, 1 paginas
YK0361	Manual de usuario Senco YK0361 User Manual, 4 paginas
2N1	Manual de usuario Senco 2N1 User Manual, 4 paginas
32	Manual de usuario Senco 32 User Manual, 4 paginas
CARTON CLOSERS STAPLERS	Manual de usuario Senco CARTON CLOSERS STAPLERS User Manual, 32 paginas
GT65RHA	Manual de usuario Senco GT65RHA User Manual, 73 paginas
SFW09	Manual de usuario Senco SFW09 User Manual, 29 paginas